smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.12.63+deb13-amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 870 EVO 1TB Serial Number: S6PUNF0RA06108V LU WWN Device Id: 5 002538 f41a6e104 Firmware Version: SVT01B6Q User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 10 20:18:24 2026 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 11 9 Power_On_Hours -O--CK 098 098 000 - 5233 12 Power_Cycle_Count -O--CK 093 093 000 - 6709 177 Wear_Leveling_Count PO--C- 099 099 000 - 17 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 099 099 010 - 11 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 099 099 010 - 11 187 Uncorrectable_Error_Cnt -O--CK 099 099 000 - 5 190 Airflow_Temperature_Cel -O--CK 081 049 000 - 19 195 ECC_Error_Rate -O-RC- 199 199 000 - 5 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 72 241 Total_LBAs_Written -O--CK 099 099 000 - 38896248627 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 5 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [0] occurred at disk power-on lifetime: 1944 hours (81 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 29 74 f5 b8 40 00 Error: UNC 2048 sectors at LBA = 0x2974f5b8 = 695530936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.263 READ DMA EXT 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.263 READ DMA EXT 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.263 READ DMA EXT 25 00 00 08 00 00 00 29 75 05 b8 40 05 00:45:53.263 READ DMA EXT 25 00 00 08 00 00 00 29 74 fd b8 40 05 00:45:53.263 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 1944 hours (81 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 29 74 f5 b8 40 00 Error: UNC 2048 sectors at LBA = 0x2974f5b8 = 695530936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.171 READ DMA EXT 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.171 READ DMA EXT 25 00 00 08 00 00 00 29 75 05 b8 40 05 00:45:53.171 READ DMA EXT 25 00 00 08 00 00 00 29 74 fd b8 40 05 00:45:53.171 READ DMA EXT 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.171 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 1944 hours (81 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 29 74 f5 b8 40 00 Error: UNC 2048 sectors at LBA = 0x2974f5b8 = 695530936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.080 READ DMA EXT 25 00 00 08 00 00 00 29 75 05 b8 40 05 00:45:53.080 READ DMA EXT 25 00 00 08 00 00 00 29 74 fd b8 40 05 00:45:53.080 READ DMA EXT 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:53.080 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 40 05 00:45:53.080 READ LOG EXT Error 2 [1] occurred at disk power-on lifetime: 1944 hours (81 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 08 00 00 00 29 74 f5 b8 40 00 Error: UNC 2048 sectors at LBA = 0x2974f5b8 = 695530936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 29 74 f5 b8 40 05 00:45:52.984 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 40 05 00:45:52.984 READ LOG EXT 60 08 00 00 28 00 00 29 74 fd b8 40 05 00:45:52.984 READ FPDMA QUEUED 60 08 00 00 20 00 00 29 74 f5 b8 40 04 00:45:52.984 READ FPDMA QUEUED 60 08 00 00 18 00 00 29 74 ed b8 40 03 00:45:52.984 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 256 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 19/40 Celsius Lifetime Min/Max Temperature: 19/51 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (98) Index Estimated Time Temperature Celsius 99 2026-11-09 23:00 29 ********** 100 2026-11-09 23:10 29 ********** 101 2026-11-09 23:20 29 ********** 102 2026-11-09 23:30 28 ********* 103 2026-11-09 23:40 28 ********* 104 2026-11-09 23:50 27 ******** 105 2026-11-10 00:00 27 ******** 106 2026-11-10 00:10 ? - 107 2026-11-10 00:20 28 ********* 108 2026-11-10 00:30 27 ******** ... ..( 2 skipped). .. ******** 111 2026-11-10 01:00 27 ******** 112 2026-11-10 01:10 26 ******* 113 2026-11-10 01:20 ? - 114 2026-11-10 01:30 ? - 115 2026-11-10 01:40 25 ****** 116 2026-11-10 01:50 26 ******* 117 2026-11-10 02:00 ? - 118 2026-11-10 02:10 27 ******** 119 2026-11-10 02:20 28 ********* 120 2026-11-10 02:30 ? - 121 2026-11-10 02:40 28 ********* 122 2026-11-10 02:50 27 ******** 123 2026-11-10 03:00 27 ******** 124 2026-11-10 03:10 26 ******* 125 2026-11-10 03:20 28 ********* 126 2026-11-10 03:30 29 ********** 127 2026-11-10 03:40 28 ********* 0 2026-11-10 03:50 28 ********* 1 2026-11-10 04:00 28 ********* 2 2026-11-10 04:10 ? - 3 2026-11-10 04:20 22 *** 4 2026-11-10 04:30 24 ***** 5 2026-11-10 04:40 25 ****** 6 2026-11-10 04:50 ? - 7 2026-11-10 05:00 26 ******* 8 2026-11-10 05:10 26 ******* 9 2026-11-10 05:20 27 ******** 10 2026-11-10 05:30 28 ********* 11 2026-11-10 05:40 28 ********* 12 2026-11-10 05:50 28 ********* 13 2026-11-10 06:00 27 ******** ... ..( 5 skipped). .. ******** 19 2026-11-10 07:00 27 ******** 20 2026-11-10 07:10 26 ******* 21 2026-11-10 07:20 ? - 22 2026-11-10 07:30 26 ******* 23 2026-11-10 07:40 27 ******** 24 2026-11-10 07:50 ? - 25 2026-11-10 08:00 ? - 26 2026-11-10 08:10 22 *** 27 2026-11-10 08:20 25 ****** 28 2026-11-10 08:30 25 ****** 29 2026-11-10 08:40 ? - 30 2026-11-10 08:50 26 ******* 31 2026-11-10 09:00 26 ******* 32 2026-11-10 09:10 26 ******* 33 2026-11-10 09:20 ? - 34 2026-11-10 09:30 28 ********* 35 2026-11-10 09:40 27 ******** ... ..( 5 skipped). .. ******** 41 2026-11-10 10:40 27 ******** 42 2026-11-10 10:50 28 ********* 43 2026-11-10 11:00 27 ******** 44 2026-11-10 11:10 27 ******** 45 2026-11-10 11:20 ? - 46 2026-11-10 11:30 28 ********* 47 2026-11-10 11:40 27 ******** 48 2026-11-10 11:50 27 ******** 49 2026-11-10 12:00 ? - 50 2026-11-10 12:10 29 ********** 51 2026-11-10 12:20 30 *********** 52 2026-11-10 12:30 30 *********** 53 2026-11-10 12:40 28 ********* 54 2026-11-10 12:50 29 ********** 55 2026-11-10 13:00 ? - 56 2026-11-10 13:10 23 **** 57 2026-11-10 13:20 25 ****** 58 2026-11-10 13:30 26 ******* 59 2026-11-10 13:40 26 ******* 60 2026-11-10 13:50 28 ********* 61 2026-11-10 14:00 28 ********* 62 2026-11-10 14:10 28 ********* 63 2026-11-10 14:20 29 ********** 64 2026-11-10 14:30 29 ********** 65 2026-11-10 14:40 29 ********** 66 2026-11-10 14:50 28 ********* 67 2026-11-10 15:00 29 ********** 68 2026-11-10 15:10 29 ********** 69 2026-11-10 15:20 28 ********* 70 2026-11-10 15:30 28 ********* 71 2026-11-10 15:40 27 ******** 72 2026-11-10 15:50 27 ******** 73 2026-11-10 16:00 ? - 74 2026-11-10 16:10 27 ******** 75 2026-11-10 16:20 27 ******** 76 2026-11-10 16:30 27 ******** 77 2026-11-10 16:40 ? - 78 2026-11-10 16:50 27 ******** 79 2026-11-10 17:00 28 ********* 80 2026-11-10 17:10 ? - 81 2026-11-10 17:20 ? - 82 2026-11-10 17:30 23 **** 83 2026-11-10 17:40 25 ****** 84 2026-11-10 17:50 26 ******* 85 2026-11-10 18:00 27 ******** 86 2026-11-10 18:10 27 ******** 87 2026-11-10 18:20 28 ********* 88 2026-11-10 18:30 28 ********* 89 2026-11-10 18:40 27 ******** 90 2026-11-10 18:50 27 ******** 91 2026-11-10 19:00 ? - 92 2026-11-10 19:10 28 ********* 93 2026-11-10 19:20 30 *********** 94 2026-11-10 19:30 29 ********** 95 2026-11-10 19:40 ? - 96 2026-11-10 19:50 ? - 97 2026-11-10 20:00 ? - 98 2026-11-10 20:10 19 - SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 6709 --- Lifetime Power-On Resets 0x01 0x010 4 5233 --- Power-on Hours 0x01 0x018 6 38896248627 --- Logical Sectors Written 0x01 0x020 6 563295290 --- Number of Write Commands 0x01 0x028 6 54842234339 --- Logical Sectors Read 0x01 0x030 6 1029634780 --- Number of Read Commands 0x01 0x038 6 1626000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 5 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 13556 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 21 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC